Home / Products / Bimetallic Wear Plates
Wear Parts

Bimetallic Wear Plates (BT-CW)

A hard wear layer on a tough steel backing, cut, drilled and formed to your drawing - for chutes, hoppers and transfer points.

Overview

A bimetallic wear plate - often written bimetal wear plate - is a composite steel plate: a hard, abrasion-resistant layer bonded to a tough structural steel backing. BT-CW is ours. It is built for surfaces where material slides continuously and a plain steel liner wears through - chute linings, hopper walls, transfer points, discharge spouts and loader or excavator wear surfaces.

The two layers do different jobs. The wear layer faces the material stream and resists sliding abrasion; the backing absorbs impact, carries the bolt loads and holds the plate flat against the structure. That combination is why a bimetallic plate can be thinner than a cast wear block and still be bolted to a chute wall.

Two names are often confused with it. A bimetal strip is the thin two-metal strip used in thermostats and switches. Copper-clad steel is a clad metal chosen for conductivity or corrosion resistance. Neither is a wear plate. If your drawing is for a clad metal rather than a wear liner, say so and we will point you to the right supplier instead of quoting a wear plate.

Where a bimetallic plate is the right choice

Composite wear plate, bimetallic plate: the same thing?

In the trade the two names describe the same construction: a hard wear layer welded onto a structural steel backing. We call ours BT-CW; buyers often ask for a "composite wear plate" or a "bimetal plate", and both arrive at the same sheet.

Build-ups run 6+4, 8+6 and 10+10 mm, and hardness is checked on every plate with a Leeb tester - typically 54-64 HRC for this family. If your enquiry says "composite wear plate", nothing needs translating: send the drawing and the duty, and the build-up follows from that.

Specifications

TypeBT-CW bimetallic (composite) wear plate
ConstructionHard wear layer bonded to a structural steel backing
Wear-face hardnessTested on every plate with a Leeb tester; typically 54-64 HRC for this family - take the exact value from the specification
Build-upQuoted as wear layer + backing, e.g. 6+4, 8+6 or 10+10 mm; confirmed against duty and drawing
BackingCarbon structural steel, grade to drawing
Plate sizeCut to drawing; large plates available
FixingBolt holes, countersunk holes, weld-on, plug weld
FlatnessChecked against the structure before dispatch
Lead time7-20 days, confirmed with the quote

Choosing the build-up

The build-up is written as wear layer + backing. The wear layer is the sacrifice; the backing carries the load and the fixing. Typical industry build-ups look like this - use them as a starting point, not a substitute for the duty:

Build-up4+4 mm - light sliding abrasion, small chutes, low headroom.
6+4 mm - general chute and hopper linings, moderate impact.
8+6 mm - the common heavy-duty request: coarse material, longer intervals between stops.
10+10 mm - high wear allowance, large lumps, structures that can carry the weight.

Two checks decide more than the number. First, the wear rate of the liner being replaced: if it lasted 4,000 hours and you want 12,000, you need roughly three times the wear allowance, not a thicker backing. Second, the structure: bolt size, hole spacing and the weight the wall can carry. Send both and the build-up can be settled on the drawing.

Bimetallic, chromium carbide or white iron?

Bimetallic plateSolid wear layer on a structural backing. Good where the liner sees sliding abrasion plus moderate impact, and where it must be formed, drilled and bolted. The all-round choice for chutes and hoppers.
Chromium carbide overlayCarbide-rich weld overlay on mild steel. Very high abrasion resistance at the surface; less tolerant of impact and of tight forming. Strong where the duty is pure sliding abrasion.
White ironCast or laminated high-chrome iron. Excellent abrasion resistance, brittle under impact, and usually fixed as blocks or tiles rather than drilled plates.

Full comparison: bimetallic vs chromium carbide vs white iron →

CORC-g® and BT-CW: what the comparison covers

CORC-g® is the compound steel wear plate made by Josua CORTS Sohn GmbH in Germany. It is a registered trademark of CORTS, and it is the name many mill and sinter-plant drawings carry because that is the plate the OEM fitted. BT-CW is our own designation for a plate of the same construction: a compound steel bonded as two solid metals, with a hardened tool-steel wear face (about 25% of the section) and a tough, low-carbon backing (about 75%), supplied as an independent CORC-g®-equivalent alternative, and made to CORC-g® drawings where the drawing specifies it. We are not a CORTS agent, distributor or licensee, and BT-CW is not a CORTS product.

The three grades line up with the three duties CORC-g® drawings usually describe - equivalent in construction and duty, not in origin:

BT-CW-BWear face 58-60 HRC; hard layer about 25% of the section (6 mm on a 25 mm plate), low-carbon backing. General sliding abrasion: chutes, hoppers, transfer points. The standard-wear equivalent.
BT-CW-BSWear face 54-58 HRC; hard layer about 25% of the section, stainless backing. Wet, salty or corrosive material. The stainless (rostfrei) equivalent.
BT-CW-BEWear face 60-64 HRC; hard layer about 25% of the section (8 mm on a 32 mm plate), low-carbon backing. Coarse lumps, high impact, mill housings and bearing seats. The heavy-wear equivalent.

Bond strength is 500-600 N/mm² on the interface shear test for all three grades. What we do not claim is identical chemistry or identical service life: the wear layer is a high-alloy tool steel to our own specification, and life depends on the duty. Where a drawing calls for CORC-g®, send the hardness and case depth written on it - for example 58-60 HRC at 7.5 mm - and we check the section against those figures before quoting.

What to send with an enquiry

What we check before dispatch

Product images

Typical applications

Chutes and hoppers

Liner layout, fixing and build-up for transfer points.

Read the guide →

Mining and aggregate handling

Discharge spouts and bins

Excavator and loader wear parts

Cement and steel plant liners

FAQ

Related products

Related: CORC-G, the two-layer liner for mill housings and chocks

Need a quote or a custom part?

Send your drawing, sample photo or specification - we reply within 1 business day.

Request a Quote