Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

C92200

Navy M Tin Bronze (88-6-2)  |  ASTM B584  |  UNS C92200  |  SAE 620 (J461 / J462)

We cast and machine this grade. Bushings, bearings, valve bodies and custom parts to drawing  View products

Chemical Composition (%)

Cu86.0-90.0
Sn5.5-6.5
Pb1.0-2.0
Zn3.0-5.0
Ni1.0 max
Fe0.25 max
P0.05 max
Sb0.05 max
S0.05 max
Al / Si0.005 max each

Limits as published for the ASTM designation; single values are maximums unless shown as a range. Cu is stated as the balance.

Mechanical & Physical Properties

Tensile strength234 MPa min (34 ksi)
Yield strength110 MPa min (16 ksi)
Elongation24% min
Hardness65 HB (typical)
Density8.63 g/cm³
Machinability42 (free-cutting brass = 100)
Impact strengthabout 26 J (19 ft-lb)
Fatigue strengthabout 76 MPa (11 ksi)

Minimum values are standard limits; hardness and machinability are typical values unless marked as minimum.

C92200 composition ranges
Published composition ranges for C92200 (bar = midpoint, whisker = range).

Typical Applications

valve bodiespump bodies and coversglandsflangesyokessteam fittingsmarine hardware

Grade Overview

C92200, the Navy M bronze, is the standard leaded tin bronze for pressure-tight valve and pump castings: about 88% copper, 6% tin, 2% lead and 4% zinc. It was developed for naval and marine service, where a casting must hold pressure, resist water and steam, and still machine and assemble reliably. Published limits are 234 MPa minimum tensile strength, 110 MPa minimum yield, 24% minimum elongation and about 65 HB typical, with a machinability rating of 42 - noticeably better than the lead-free gun metals because of the lead addition.

The alloy is deliberately balanced rather than maximised: the 1-2% lead gives pressure tightness and machinability, the zinc improves fluidity and strength, and the modest tin content keeps cost and casting difficulty down. It is not a high-load bearing bronze and it is not a seawater-immersion alloy in the way the nickel aluminum bronzes are, but for valve bodies, pump casings, glands, flanges and yokes it is one of the most widely specified cast copper alloys in existence.

Cast copper alloy family strength and hardness
Strength and hardness across the cast copper alloy family, from published ASTM limits.

Microstructure and Behaviour

Cored alpha solid solution with fine lead particles distributed through the matrix. The lead does two jobs: it fills micro-shrinkage and improves pressure tightness, and it lubricates the cutting tool. Structure control is about uniform tin distribution and sound feeding rather than heat treatment, and no thermal treatment is applied.

Standards and Equivalents

C92200 is ordered to ASTM B584 for sand castings; SAE 620 (J461/J462), QQ-C-390 and the old military specification Mil-C-22229 are the traditional equivalents. The nearest GB/T 1176 grade is ZCuSn6Zn6Pb3, an approximate rather than exact match; check the lead and zinc ranges before substituting. For continuous castings, note that the phosphorus limit is relaxed to 1.5% in some specifications - order to the standard that matches the form.

Selecting C92200

Choose C92200 for pressure-retaining valve bodies, pump bodies and covers, glands, flanges and yokes in water, steam and general marine service. Against C83600 (85-5-5-5) it has slightly more tin and less zinc, giving better corrosion resistance and a little more strength at similar machinability. Against C90300 it contains lead, so it machines and seals more easily but is not a lead-free choice. Against C90700 it is softer and tougher, with much better castability. It is not the grade for high-load bearings.

How to Specify C92200 on a Drawing

Casting and Machining Notes

C92200 casts well and is tolerant of ordinary foundry practice, which is a large part of why it is so widely used. Keep the melt clean and deoxidised, feed the heavy sections and avoid turbulence in the gating system; most pressure-tightness failures come from gas or shrinkage rather than from composition. It welds with care but weld repair on pressure-retaining surfaces should be agreed in advance. Machining at 42 is straightforward, with the lead phase breaking chips.

Pressure tightness and valve service

For valve bodies and pump casings the acceptance test matters as much as the alloy. Agree the hydrostatic pressure, the hold time, whether leaking castings may be impregnated and whether weld repair is allowed. A sound C92200 casting is routinely pressure tight; a gassy one will leak no matter how good the chemistry looks on paper.

Frequently asked questions about C92200

What is Navy M bronze?

Navy M is the traditional name for C92200, an 88-6-2-4 leaded tin bronze developed for naval valve and pump castings. The UNS number is what should appear on a modern drawing.

C92200 or C83600?

Both are leaded pressure-tight casting alloys. C83600 (85-5-5-5) is a red brass with more zinc and less tin; C92200 has more tin and less zinc, giving better corrosion resistance and slightly higher strength at similar machinability. For water and steam valve bodies either works; C92200 is the more corrosion-resistant choice.

Can C92200 be used in seawater?

It is used in marine hardware and has good resistance to water and steam, but it is not a dedicated seawater-immersion alloy. For continuous seawater service with erosion, a nickel aluminum bronze or cupronickel is the safer specification.

Does C92200 contain lead?

Yes, 1-2%. That is what gives it pressure tightness and a machinability rating of 42, but it also means the alloy is restricted in drinking-water and food-contact applications. Confirm the lead limit for the destination market.

What pressure should a C92200 valve body be tested to?

The test pressure is a design decision, not an alloy property. State it on the drawing with the hold time and acceptance criterion, and agree with the foundry whether impregnation or weld repair is permitted for any casting that fails.

Can C92200 be welded?

It can be welded with care, but weld repair of pressure-retaining surfaces should be agreed before casting. The heat input affects the lead distribution and can create new porosity, so a weld repair is not automatically better than a sound original casting.

Data compiled from published ASTM B584, B505/B505M and B271 limits and from mill specification sheets (Diversified Bronze, Concast, St. Paul Foundry); for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related grades

C83600 · C90300 · C93200 · C90500  |  All 62 grades in the library

← Back to Alloy Grades