Chemical Composition (%)
| Cu | 86.0-89.0 |
|---|---|
| Sn | 9.0-11.0 |
| Zn | 1.0-3.0 |
| Pb | 0.30 max |
| Ni | 1.0 max |
| Fe | 0.20 max |
| P | 0.05 max |
| Sb | 0.20 max |
| S | 0.05 max |
| Al / Si | 0.005 max each |
Limits as published for the ASTM designation; single values are maximums unless shown as a range. Cu is stated as the balance.
Mechanical & Physical Properties
| Tensile strength | 276-310 MPa (40-45 ksi) |
|---|---|
| Yield strength | 124-152 MPa (18-22 ksi) |
| Elongation | 20-25% |
| Hardness | 70-80 HB (typical) |
| Density | 8.63 g/cm³ |
| Machinability | 30 (free-cutting brass = 100) |
| Electrical conductivity | 11% IACS |
Minimum values are standard limits; hardness and machinability are typical values unless marked as minimum.

Typical Applications
Grade Overview
C90500 is the traditional gun metal: about 88% copper, 10% tin and 2% zinc, lead-free. It is one of the oldest bearing and valve alloys in continuous use, and it remains a sensible default where a lead-free tin bronze with good casting behaviour and corrosion resistance is wanted. Published limits are 276-310 MPa tensile strength, 124-152 MPa yield strength, 20-25% elongation and 70-80 HB, with a machinability rating of about 30. Density is 8.63 g/cm³, slightly lower than C90300 because of the higher tin and lower zinc.
Compared with C90300, the extra tin raises hardness and wear resistance at much the same strength and ductility. The alloy casts well, pressure-tight, and resists attack in water, steam and marine atmospheres. It is not a high-load bearing bronze; for heavy pressure and high speed the high-leaded grades or the harder 65 bronze are used. C90500 is best understood as the general-purpose gun metal for pump and valve work where lead is excluded.

Microstructure and Behaviour
The structure is alpha solid solution with cored dendrites; at 10% tin, slow cooling can leave tin-rich delta phase at the grain boundaries, which lowers ductility even though strength holds up. Feeding and cooling control therefore matter more than nominal composition. No heat treatment is applied.
Standards and Equivalents
Order to ASTM B584 (sand), B505/B505M (continuous cast) or B271 (centrifugal), with SAE J461/J462 listing the same UNS number. The nearest GB/T 1176 grade is ZCuSn10Zn2, an approximate rather than an exact match; check composition before substituting either way.
Selecting C90500
Choose C90500 when the part is a lead-free tin bronze of moderate duty: pump impellers, valve bodies, gears, lightly loaded bearings, piston rings and steam or marine fittings. Against C90300 it trades a little ductility for hardness and wear resistance. Against C92200 it has no lead and lower impact toughness, but better corrosion resistance and no lead-leaching concern. Against C90700 it is softer and much easier to cast and machine. It is not the grade for high-speed, heavily loaded bearings.
How to Specify C90500 on a Drawing
- UNS number — C90500.
- Standard and form — B584 sand, B505 continuous, B271 centrifugal.
- Temper — as-cast (F).
- Test bars — separately cast, with the sampling frequency stated.
- Pressure test — for valve and pump bodies, name the test pressure and acceptance rule.
- Bearing features — oil grooves, clearances and bore tolerance called out on the drawing, not left to the foundry.
Casting and Machining Notes
C90500 pours well and reproduces detail, but the 9-11% tin range needs care: keep pouring temperature moderate, feed the heavy sections and avoid long holding times that coarsen the structure. Welding is not recommended for pressure-retaining surfaces. Machining behaves like a lead-free bronze - sharp tools, positive rake and steady feed - and tool wear is higher than with leaded grades.
Gun metal in pump and valve service
The combination of pressure tightness and corrosion resistance keeps gun metal in pump and valve work where cast iron is not good enough and stainless is too expensive. For seawater-adjacent service, confirm the actual medium and temperature with the foundry: gun metal performs well in many marine applications but is not a universal seawater alloy, and erosion at high flow velocities is a separate design question from corrosion.
Frequently asked questions about C90500
Is C90500 the same as gun metal?
Yes - C90500 is the standard UNS designation for the traditional 88-10-2 gun metal. Older drawings may call it gun metal, admiralty gun metal or SAE 620 series; the UNS number is what should appear on a modern purchase order.
C90500 or C90300?
C90500 has more tin (9-11% versus 7.5-9%), giving 70-80 HB against 65-75 HB and slightly better wear resistance at similar strength. C90300 is a little more ductile and cheaper in tin. Choose C90500 for wear-prone valve and pump parts, C90300 for general pressure-tight castings.
Can C90500 be used in seawater?
It is used in marine fittings and has good corrosion resistance, but it is not a dedicated seawater alloy. For continuous seawater immersion, especially with high flow velocity, review erosion-corrosion and consider a nickel aluminum bronze or cupronickel instead.
Why is the machinability rating only 30?
Because the alloy is lead-free. There is no soft phase to lubricate the tool and break the chip, so cutting forces are higher and surface finish depends on tool geometry and feed. Budget more machining time than for C93200.
Does C90500 need heat treatment?
No. Properties are as-cast, and the standard does not call for solution or precipitation treatment. Stress relief may be used after rough machining on thin or dimensionally critical parts.
What is the difference between B584 and B505 for C90500?
B584 covers sand castings, B505 continuous-cast rod and bar. The same UNS number appears in both, but test-bar location, section size and acceptance rules differ. Order to the standard that matches the form you are buying, and say so on the drawing.
Data compiled from published ASTM B584, B505/B505M and B271 limits and from mill specification sheets (Diversified Bronze, Concast, St. Paul Foundry); for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.
Related grades
C90300 · C92200 · C93200 · C83600 | All 62 grades in the library