Chemical Composition (%)
| Cu | 88.0-90.0 |
|---|---|
| Sn | 10.0-12.0 |
| Pb | 0.50 max |
| Zn | 0.50 max |
| Fe | 0.15 max |
| Ni | 0.50 max |
| P | 0.30 max |
| Al / Si | 0.005 max each |
| S | 0.05 max |
| Sb | 0.20 max |
Limits as published for the ASTM designation; single values are maximums unless shown as a range. Cu is stated as the balance.
Mechanical & Physical Properties
| Tensile strength | 276 MPa min (40 ksi) |
|---|---|
| Yield strength | 172 MPa min (25 ksi) |
| Elongation | 10% min |
| Hardness | 102 HB (typical) |
| Density | 8.77 g/cm³ |
| Machinability | 20 (free-cutting brass = 100) |
| Modulus of elasticity | 103 GPa |
| Thermal conductivity | 70.6 W/(m·K) |
Minimum values are standard limits; hardness and machinability are typical values unless marked as minimum.

Typical Applications
Grade Overview
C90700 is the 65 bronze: 88-90% copper and 10-12% tin, with lead, zinc and phosphorus held to maxima. It is the harder end of the standard tin-bronze family, with a minimum tensile strength of 276 MPa, minimum yield of 172 MPa, minimum elongation of 10% and a typical hardness of about 102 HB. Machinability is rated 20, the lowest of the common cast bronzes, because the high tin content makes the alloy hard and abrasive to tools. In exchange it gives wear resistance and load capacity that the softer gun metals cannot match.
The grade is a workhorse for worm gears and heavily loaded bearings, where the combination of strength, hardness and low friction against a steel worm is more important than ductility. Its low elongation is the price: C90700 does not tolerate shock or misalignment the way C90300 or C93200 does, and it is not a repair-welding grade. It is also the grade that most rewards good foundry practice, because shrinkage porosity in a hard alloy is much harder to recover than in a soft one.

Microstructure and Behaviour
Alpha solid solution with a high tin content; slow cooling produces delta phase at grain boundaries and a hard, less ductile structure. Phosphorus is present only as a residual impurity in this grade, so the hardening comes from tin in solution and from the cast structure, not from phosphide particles as in a phosphor bronze.
Standards and Equivalents
ASTM B505/B505M covers continuous-cast rod and bar and is the usual reference for C90700; B584 covers sand castings. SAE 65 (J461/J462) is the traditional designation. The nearest GB/T 1176 grades are the high-tin tin bronzes such as ZCuSn10P1 and ZCuSn10Zn2, but none is an exact match: C90700 carries no deliberate phosphorus addition, so do not substitute on the basis of the tin content alone.
Selecting C90700
Choose C90700 for worm gears, heavily loaded bearings, pump parts and valve trim where the part must carry load at moderate speed and the lubrication is reliable. Against C90500 it is much harder (about 102 HB versus 70-80) and stronger, at half the ductility. Against C93200 it is harder and stronger but far less forgiving of dirt, misalignment and interrupted lubrication. Against C93800 it trades embeddability and machinability for load capacity. If the duty includes shock, use a softer bronze; if it includes high load at speed, C90700 is the right family.
How to Specify C90700 on a Drawing
- UNS number — C90700, and the traditional SAE 65 reference if the customer uses it.
- Standard — B505 for continuous cast, B584 for sand cast.
- Temper — as-cast (F).
- Test bars — separately cast, per heat or per lot as agreed.
- Hardness — state whether the 102 HB typical value is a reference or an acceptance limit; the standard sets a typical, not a minimum.
- Worm-gear details — tooth form, backlash and bore tolerance belong on the drawing; the alloy alone does not define the gear.
Casting and Machining Notes
High-tin bronze is less forgiving than gun metal: the freezing range is wide, shrinkage is significant and feeding must be generous. Keep pouring temperature under control to limit tin segregation, and do not rely on welding to recover porosity on working surfaces. Machining at a rating of 20 calls for sharp carbide, light depths of cut and attention to tool wear; the alloy work-hardens and will punish a dull edge.
Bearing duty and lubrication
C90700 is a bearing alloy for steady load and reliable lubrication. Design the bearing with a proper oil film, a running-in period and a hardness difference against the shaft; do not run it dry or on an interrupted oil supply. In dirty service, a leaded bronze such as C93200 or C93800 embeds grit better and will usually outlast the harder alloy despite lower nominal strength.
Frequently asked questions about C90700
What is C90700 used for?
Worm gears, heavy-duty bearings, pump parts and valve trim. It is the standard 65 bronze with about 10-12% tin and a typical hardness of 102 HB, chosen where load capacity and wear resistance matter more than ductility.
C90700 or C90500?
C90700 is much harder (about 102 HB versus 70-80) and stronger, with only 10% minimum elongation. C90500 is softer, tougher and easier to cast and machine. Use C90700 for loaded worm gears and steady bearings; use C90500 for pump and valve castings and light bearings.
Can C90700 replace C93200?
It is harder and stronger but far less embeddable and much harder to machine (rating 20 versus about 70). In clean, well-lubricated, steady load the swap can work; in dirty or shock-loaded service C93200 is usually the better bearing.
Why is the machinability rating so low?
High tin content makes the alloy hard and abrasive, and there is no lead to lubricate the cut. Expect higher tool wear, lower cutting speeds and more attention to rigid setup than with C93200.
Does C90700 contain phosphorus?
Only as a residual impurity, with a published maximum of 0.30%. It is not a phosphor bronze in the sense of a deliberately phosphorus-hardened grade, so do not substitute it for one on the assumption that the chemistry is equivalent.
Can C90700 be welded?
Not for working surfaces. Repair welding of high-tin bronze is unreliable and is normally excluded for bearing and gear surfaces. Cast it sound, or scrap and recast.
Data compiled from published ASTM B584, B505/B505M and B271 limits and from mill specification sheets (Diversified Bronze, Concast, St. Paul Foundry); for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.
Related grades
C90500 · C93200 · C93800 · C90300 | All 62 grades in the library