Chemical Composition (%)
| Sb | 4.0~5.0 |
|---|---|
| Cu | 4.0~5.0 |
| Sn | Balance |
Mechanical & Physical Properties
| Hardness | ≈20 HBW |
|---|---|
| Density | ≈7.3 g/cm³ |
Typical Applications
Grade Overview
The lowest-antimony tin-based Babbitt, used for high-speed bearings, thin-wall bushes and turbine bearings. The low antimony content gives the best toughness and high ductility in the family, so it accommodates thin poured layers and resists shock while retaining corrosion, heat and wear resistance; hardness is about 20 HBW. The cost is the lowest strength and hardness of the three tin-based grades and therefore limited load capacity, so it is not suitable for heavy duty. It is used mainly for high-speed bushes where ductility and shock resistance matter. Keep the poured layer as thin as possible to exploit the toughness, ensure a good oil film and oil supply in service, and avoid deformation or accelerated wear from excessive load; it should not be used at high load or elevated temperature, and lining thickness must be controlled to the design. It is often used where the shaft runs fast and the load is light, and because the alloy is soft it should be protected from dirt and from abrasive contamination of the oil.
Selecting ZSnSb4Cu4
ZSnSb4Cu4 is a tin-based Babbitt with less antimony than the other tin-based grades here, used for high-speed bearings, thin-wall bushes and turbine bearings. The low antimony content gives it more toughness and ductility than the plain tin-based grades, so it accommodates thin poured layers and resists shock while retaining corrosion, heat and wear resistance; hardness is about 20 HBW. The cost is lower strength and hardness than the other plain tin-based grades, and therefore limited load capacity, so it is not suitable for heavy duty. Where more load has to be carried, ZSnSb8Cu4 or ZSnSb11Cu6 is the step up; where cost governs and the load is medium, the lead-based ZPbSb10Sn6 or ZPbSb15Sn5 is an economical alternative. The alloy is used where the shaft runs fast and the load stays light.
Working with ZSnSb4Cu4
The value of ZSnSb4Cu4 lies in toughness, so keep the poured layer as thin as the design allows and bond it well to the shell; a thick layer wastes the property that justifies the grade. Prepare and tin the backing, control the cooling rate, and stir the melt to keep the structure uniform. No heat treatment is used. In service, maintain a good oil film and a reliable oil supply, avoid excessive load that would deform the soft lining, and protect the bearing from dirt and abrasive contamination of the oil, which a soft alloy cannot tolerate. Running temperature stays low because the lining is soft and thin.
Frequently asked questions about ZSnSb4Cu4
Why is it used for thin linings?
The low antimony content gives the alloy more toughness and ductility than the other plain tin-based grades, so a thin layer can follow the shell, resist shock and still run reliably. Thick layers waste that toughness and cost more, so the design keeps the lining thin. Ensuring a sound bond is essential when the layer is thin.
What load can ZSnSb4Cu4 carry?
Hardness is about 20 HBW, lower than the other plain tin-based grades, so load capacity is limited and heavy duty is not suitable. It suits high-speed, lightly loaded bearings where shock resistance and ductility matter more than strength. Where more load must be carried, ZSnSb8Cu4 or ZSnSb11Cu6 is used instead.
Why is oil cleanliness important?
The alloy is soft at about 20 HBW, so abrasives in the oil embed in or score the lining and accelerate wear. A clean, reliable oil supply and a stable film protect the bearing and preserve its running-in characteristics. Contamination is a common cause of premature failure in soft-lined bearings, so filtration and sealing deserve attention.
Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.