Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Bearing Alloy (Babbitt)

ZPbSb15Sn10

ZPbSb15Sn10 Lead-Based Babbitt (15-10 White Metal)  |  Bearing Alloy (Babbitt)  |  GB/T 1174

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Sb14.0~16.0
Sn9.0~11.0
PbBalance

Mechanical & Physical Properties

Hardness≈24 HBW
Density≈9.8 g/cm³

Typical Applications

medium-speed bearingsmoderate-shock bearingshigh-temperature bearings

Grade Overview

A lead-based Babbitt with medium antimony and tin content, used for medium-speed bearings, bearings subject to moderate shock and high-temperature bearings. Compared with ZPbSb16Sn16Cu2 it offers better impact toughness and ductility and good running-in behaviour, and after annealing its anti-friction performance and toughness improve further; hardness is about 24 HBW, but the coefficient of friction is relatively high. Load capacity is intermediate, so it is not suited to heavy, high-speed duty without adequate lubrication. Choose it for medium-speed, moderate-load bearings that may see some shock; ensure good oil supply and running-in, respect the temperature limit, control structural uniformity when pouring, and observe the compliance requirements for lead. Stir thoroughly before pouring to avoid segregation from the density difference. Because it runs in more easily than the harder lead-based grades, it is a practical choice for bearings that cannot be run in under controlled conditions, and an annealing treatment before service can improve both toughness and anti-friction behaviour.

Selecting ZPbSb15Sn10

ZPbSb15Sn10 is a lead-based Babbitt with medium antimony and tin, intended for medium-speed bearings, bearings that see moderate shock and bearings of higher temperature. Compared with ZPbSb16Sn16Cu2 it offers better impact toughness and ductility and runs in easily, and after annealing its anti-friction behaviour and toughness improve further; hardness is about 24 HBW, while the coefficient of friction is relatively high. Load capacity is intermediate, so heavy, high-speed duty needs more lubrication than this grade can rely on. Choose ZPbSb16Sn16Cu2 where higher compressive strength and wear life are needed, ZPbSb15Sn5 for lighter duty at lower cost, ZPbSb15Sn5Cu3Cd2 where more hardness is wanted, and a tin-based grade such as ZSnSb8Cu4 where temperature or load exceed the lead-based envelope. It also runs in more easily than the harder lead-based grades.

Working with ZPbSb15Sn10

The density difference between lead and the hard phases makes segregation the main casting concern, so stir thoroughly before pouring and control the cooling rate to keep the structure uniform. The alloy pours as a lining on a steel or bronze shell; prepare the backing properly and check the bond. Annealing after casting improves both toughness and anti-friction behaviour, which is useful for bearings that cannot be run in carefully. Keep the layer even, run the bearing in, and respect the temperature limit in service. Handle lead-bearing melt and swarf under the applicable rules. Uneven cooling leaves soft and hard zones that shorten lining life.

Frequently asked questions about ZPbSb15Sn10

Why anneal this Babbitt?

Annealing after casting improves impact toughness and anti-friction behaviour, which helps bearings that cannot be run in under controlled conditions. It also makes the structure more uniform. The grade already has better toughness than ZPbSb16Sn16Cu2, so the treatment suits medium-speed, moderate-shock duty where reliability of the lining matters more than maximum load capacity.

How does it differ from ZPbSb16Sn16Cu2?

ZPbSb16Sn16Cu2 is harder, about 30 HBW, and carries more compressive load, which suits heavily loaded high-speed bearings without shock. ZPbSb15Sn10 is softer at about 24 HBW but tougher, so it tolerates moderate shock and off-centre loading better and runs in more easily. Choose by whether load or toughness is the limiting requirement.

What duty suits ZPbSb15Sn10?

It suits medium-speed bearings under moderate load that may see some shock, and bearings that run at a higher temperature than the plain grades allow. Lubrication must be reliable, because load capacity is intermediate and the coefficient of friction is relatively high. Heavy, high-speed duty belongs to a harder bearing alloy.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

ZPbSb15Sn10 vs ZPbSb10Sn6 vs ZPbSb15Sn5

These three lead-based Babbitt grades are often quoted against each other. The table below puts the published ranges side by side; use it to pick the lowest-cost grade that still meets the duty.

GradeSb %Sn %HardnessMax service temperatureTypical duty
ZPbSb10Sn69.0-11.05.0-7.0approx. 18 HBWup to 120 CAutomotive main bearings, air-compressor and oil-pump bearings; economical replacement for tin-based ZSnSb4Cu4
ZPbSb15Sn514.0-15.54.0-5.5approx. 20 HBWup to 100 CLow-speed, light-load general machinery; steady load and good lubrication required
ZPbSb15Sn1014.0-16.09.0-11.0approx. 24 HBWMedium-speed duty; confirm with applicationMedium-speed bearings with moderate shock; better running-in and toughness than ZPbSb16Sn16Cu2

Choose ZPbSb10Sn6 when cost and running-in matter and the duty stays at or below 120 C. Choose ZPbSb15Sn5 only for low-speed, light-load machinery within 100 C. Choose ZPbSb15Sn10 when the bearing sees moderate shock or needs more hardness and tin content; it is the grade we most often pour for general-purpose shells. All three are lead-based: confirm the applicable lead restrictions before specifying them for a new machine.

Related Babbitt grades

· ZPbSb15Sn5Cu3Cd2 · ZPbSb16Sn16Cu2  |  All 52 grades in the library

← Back to Alloy Grades