Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Bearing Alloy (Babbitt)

ZSnSb12Cu6Cd1

ZSnSb12Cu6Cd1 Tin-Based Babbitt (Cadmium-Bearing)  |  Bearing Alloy (Babbitt)  |  GB/T 1174

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Sb10.0~13.0
Cu4.5~6.3
Cd1.1~1.6
Ni0.3~0.6
SnBalance

Mechanical & Physical Properties

Hardness≈34 HBW
Density≈7.4 g/cm³

Typical Applications

heavy-duty bearingshigh-temperature bearingsbushes

Grade Overview

A tin-based Babbitt that adds cadmium and nickel to the tin-antimony-copper base, used for heavy-duty bearings, high-temperature bearings and bushes. Cadmium and nickel raise hardness and high-temperature strength, so the compressive load capacity is higher than that of ZSnSb11Cu6, with hardness of about 34 HBW and useful properties retained at higher temperature. The trade-off is lower ductility and toughness, so the alloy adapts less well to shock and off-centre loading, and cadmium raises environmental and occupational-health concerns. Specify it for bearings carrying higher loads at higher temperatures; check cadmium compliance and protection requirements, control segregation and structural uniformity during pouring, and avoid clearly shock-loaded duties. Treat it as cadmium-bearing material throughout casting and service, with proper protection and waste disposal. The higher hardness makes the alloy more suitable for steady heavy loads than for reversing or shock loading, and because the lining is harder it conforms less readily to the shaft, so alignment and clearance matter more than with the softer grades.

Selecting ZSnSb12Cu6Cd1

ZSnSb12Cu6Cd1 adds cadmium and nickel to the tin-antimony-copper base, raising hardness to about 34 HBW and improving high-temperature strength, so it carries more compressive load than ZSnSb11Cu6 and keeps useful properties at higher temperature. It is used for heavy-duty bearings, high-temperature bearings and bushes. The trade-off is lower ductility and toughness, so it adapts less well to shock and off-centre loading, and cadmium brings environmental and occupational-health obligations. Choose ZSnSb11Cu6 where toughness and shock tolerance decide, ZSnSb8Cu4 where a lower-antimony tin base suits thin bimetal shells, ZSnSb12Pb10Cu4 where cost matters and temperature is moderate, and ZPbSb15Sn5Cu3Cd2 when a lead-based grade with similar hardness is acceptable. It is poured as a lining on a shell, where fit and clearance matter as much as composition.

Working with ZSnSb12Cu6Cd1

Cadmium in the charge means the melt, swarf and scrap need specific protection and disposal arrangements, and those obligations continue through service and re-lining. Control segregation and cooling so the structure is uniform and the bond to the shell is sound, because a harder, less conformable lining shows up alignment and clearance problems sooner. Keep the lining thin, align the shaft carefully, and set clearance so the oil film can carry the load. Avoid clearly shock-loaded duties. Take care with pouring temperature, since the higher alloy content makes the melt less forgiving of overheating. Casting temperature should stay within the recommended pouring range.

Frequently asked questions about ZSnSb12Cu6Cd1

What are the cadmium obligations for this grade?

Cadmium at 1.1-1.6% means melting, machining, service and disposal all fall under specific protection and waste-management rules, and the same care applies at re-lining. Check the destination market's restrictions on cadmium-bearing bearing alloys before shipping. Where cadmium cannot be used, ZSnSb11Cu6 or ZPbSb16Sn16Cu2 provides a comparable bearing function without it.

When should ZSnSb11Cu6 be chosen instead?

Choose ZSnSb11Cu6 where toughness and shock tolerance decide the selection, because ZSnSb12Cu6Cd1 is harder but less ductile and adapts less well to shock and off-centre loading. Choose this cadmium-bearing grade when higher load at higher temperature is the requirement. The decision turns on whether the bearing must absorb impact or carry more load at temperature.

How does alignment affect a lining of this grade?

A harder, less conformable lining depends more on good fit than a soft one does, so alignment, clearance and shaft finish matter more. If the bearing is misaligned or the clearance is wrong, contact concentrates and the lining can be damaged before it runs in. Careful fitting and a reliable oil supply protect the lining.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related Babbitt grades

ZSnSb12Pb10Cu4 · ZSnSb4Cu4 · ZSnSb8Cu4  |  All 52 grades in the library

← Back to Alloy Grades