Chemical Composition (%)
| Cu | 60.0~66.0 |
|---|---|
| Al | 4.5~7.0 |
| Fe | 2.0~4.0 |
| Mn | 1.5~4.0 |
| Zn | Balance |
| Si (impurity) | ≤0.10 |
| Pb (impurity) | ≤0.20 |
| Sn (impurity) | ≤0.20 |
| Ni (impurity, not counted in impurity total) | ≤3.0 |
Mechanical & Physical Properties
| Tensile strength | ≥740 MPa (chill cast) |
|---|---|
| Yield strength (sigma 0.2) | ≥400 MPa (chill cast) |
| Elongation (delta) | ≥7% (chill cast) |
| Hardness | ≥170 HBW (chill cast) |
| Density | ≈8.5 g/cm³ |
Typical Applications
Grade Overview
A multi-element strengthened cast aluminum-manganese brass whose strength and hardness are the highest among cast brasses, used for bridge bearing plates, nuts and screws, wear plates and slide blocks, worm wheels, bearing shells and bushings, and valve stems and high-pressure valve bodies. Aluminum, iron and manganese form hard phases and strengthen in solid solution, so casting behaviour is good, corrosion resistance is reasonable and the alloy is weldable, with tensile strength of at least 740 MPa, yield strength of at least 400 MPa, elongation of at least 7% and hardness of at least 170 HBW in chill castings; wear resistance is excellent. The drawback is modest elongation and a tendency to stress-corrosion cracking. Use it for high-strength, high-wear pressure and wear parts; stress-relieve after welding or cold working, avoid sustained tensile stress in damp, ammonia-bearing environments, and control impurity content to keep properties stable. It is a cost-effective alternative to the aluminum bronzes where high strength and wear resistance matter more than ductility, and it both casts and machines well.
Selecting ZCuZn25Al6Fe3Mn3
ZCuZn25Al6Fe3Mn3 is a high-strength cast brass for bridge bearing plates, nuts and screws, wear plates and slide blocks, worm wheels, bearing shells and bushings, and valve stems and high-pressure valve bodies. Aluminum, iron and manganese form hard phases and strengthen in solid solution, so it reaches chill-cast tensile strength of at least 740 MPa, yield strength of at least 400 MPa and hardness of at least 170 HBW while still casting and machining well. Elongation is modest at about 7%, and the alloy is prone to stress-corrosion cracking, so sustained tensile stress in damp, ammonia-bearing environments is a design risk. It is a cost-effective alternative to aluminum bronze where high strength and wear resistance matter more than ductility; choose ZCuAl9Fe4Ni4Mn2 or ZCuAl10Fe3 where corrosion resistance leads, and ZCuZn38Mn2Pb2 where a lower-cost, lower-strength part will do.
Working with ZCuZn25Al6Fe3Mn3
Because the alloy is susceptible to stress-corrosion cracking, stress-relieve after welding or heavy cold working, and avoid designs that hold the part under sustained tensile stress in damp or ammonia-bearing service. Impurity levels matter: silicon, lead and tin are tightly limited and nickel is capped, so control the charge and verify the analysis. The alloy casts well and machines readily, which keeps production economical, and no special heat treatment is needed for as-cast properties. Wear resistance suits slide blocks, wear plates and worm wheels running against hardened surfaces, with reliable lubrication. Weld repairs are possible but must be followed by stress relief.
Frequently asked questions about ZCuZn25Al6Fe3Mn3
Is ZCuZn25Al6Fe3Mn3 prone to corrosion?
It has reasonable corrosion resistance but is prone to stress-corrosion cracking when it carries sustained tensile stress in damp, ammonia-bearing environments. Stress relief after welding or cold working reduces the risk, and the design should avoid a permanent tensile load. Where the medium is aggressive without that complication, an aluminum bronze such as ZCuAl9Fe4Ni4Mn2 is more suitable.
Can it be welded?
The alloy is weldable, but parts welded or heavily cold worked should be stress-relieved afterwards to remove the residual stresses that promote stress-corrosion cracking. Impurity limits on silicon, lead and tin, and the nickel cap, should also be checked, since composition affects response. For high-integrity pressure parts, confirm the welding procedure.
Why choose this instead of an aluminum bronze?
It combines high strength, at least 740 MPa tensile in chill castings, with high wear resistance and good casting and machining behaviour, often at lower cost than an aluminum bronze. Where corrosion resistance is the deciding factor, or where ammonia-bearing media are involved, ZCuAl10Fe3 or ZCuAl9Fe4Ni4Mn2 is the better choice.
Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.
Related cast copper alloy grades
ZCuZn35Al2Mn2Fe1 · ZCuZn38Mn2Pb2 · | C86300 | All 62 grades in the library