Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

ZCuZn38Mn2Pb2

38-2-2 Manganese Brass (Cast)  |  Cast Copper Alloy  |  GB/T 1176

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Cu57.0~60.0
Mn1.5~2.5
Pb1.5~2.5
ZnBalance

Mechanical & Physical Properties

Tensile strength≥345 MPa (chill cast)
Elongation≥18% (chill cast)
Hardness≥80 HBW (chill cast)

Typical Applications

sleevesbushingsbearing shellsslide blocksvalve-stem nuts

Grade Overview

A widely used cast manganese brass for sleeves, bushings, bearing shells, slide blocks and valve-stem nuts, in other words general structural and wear parts rather than heavy bearings. Manganese strengthens the alloy in solid solution and improves corrosion resistance, while lead improves machinability, so mechanical properties are respectable, machining is easy and casting behaviour is good: sand-cast tensile strength at least 245 MPa, elongation at least 10% and hardness about 80 HBW in chill castings. Neither strength nor corrosion resistance matches the aluminum bronzes, and dezincification and stress-corrosion cracking are the recognised risks. Specify it for cost-sensitive structural parts and wear blocks under moderate load; avoid long-term tensile stress in chloride-bearing or damp environments, stress-relieve where necessary, and check lead content against the relevant compliance requirements. Machining is a particular strength thanks to the lead addition, and the casting suits continuous production of sleeves and nuts; where corrosion resistance decides the choice, however, an aluminum bronze will serve longer.

Selecting ZCuZn38Mn2Pb2

ZCuZn38Mn2Pb2 is a widely used cast manganese brass for sleeves, bushings, bearing shells, slide blocks and valve-stem nuts, in other words general structural and wear parts rather than heavy bearings. Manganese strengthens the alloy in solid solution and improves corrosion resistance, while lead improves machinability, so properties are respectable, machining is easy and casting is straightforward, with chill-cast tensile strength of at least 345 MPa and elongation of at least 18%. Neither strength nor corrosion resistance matches the aluminum bronzes, and dezincification and stress-corrosion cracking are recognised risks. Choose ZCuZn25Al6Fe3Mn3 where high strength and wear resistance are needed, ZCuSn5Pb5Zn5 for general bearings, ZCuAl10Fe3Mn2 for corrosion duty, and check the lead content against compliance rules. Cost and easy machining are its main attractions in volume work.

Working with ZCuZn38Mn2Pb2

Dezincification and stress-corrosion cracking are the two risks to design around: avoid long-term tensile stress in chloride-bearing or damp environments and stress-relieve where the part will see sustained load, especially after welding. Control pouring so the section is sound, and check the lead content against the compliance rules for the destination, since lead is added for machinability. The alloy machines very well, which suits continuous production of sleeves and nuts, and it casts reliably in quantity. No special heat treatment is needed for as-cast properties. Lubricate sliding applications and keep loads moderate, because hardness is around 80 HBW in chill castings.

Frequently asked questions about ZCuZn38Mn2Pb2

What are the corrosion risks with ZCuZn38Mn2Pb2?

As a zinc-rich brass it can suffer dezincification in chloride-bearing water, and it is susceptible to stress-corrosion cracking where sustained tensile stress meets a damp or ammoniacal environment. Keep service conditions moderate, stress-relieve parts that will carry sustained load, and choose an aluminum bronze where corrosion resistance leads the selection.

Why is lead added to this brass?

Lead at 1.5-2.5% works as a machinability aid, giving short chips and clean finishes, which is why the alloy suits volume production of sleeves and nuts. It does not raise strength. Because lead is restricted in some markets and applications, confirm the compliance position for the destination before specifying the grade.

When should stress relief be applied?

Apply stress relief after welding or heavy cold working, and consider it for parts that will run under sustained tensile stress in a damp or chloride-bearing environment, because that is where stress-corrosion cracking occurs. Castings used under compressive load only are less at risk. The treatment lowers residual stress without changing the basic as-cast properties.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related cast copper alloy grades

· ZCuZn40Mn3Fe1 · C96900  |  All 52 grades in the library

← Back to Alloy Grades