Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

C86300

Manganese Bronze / High-Strength Yellow Brass  |  Cast Copper Alloy  |  ASTM B505 / B271  |  UNS C86300

We make this grade. Copper alloy castings and machined bushings to this specification, with certificate of analysis  View products

Chemical Composition (%)

Cu60.0-66.0
Zn22.0-28.0
Al5.0-7.5
Mn2.5-5.0
Fe2.0-4.0
Ni1.00 max
Pb0.20 max
Sn0.20 max

Limits as published for the ASTM designation; single values are maxima.

Mechanical & Physical Properties

Tensile strength>= 758 MPa (110 ksi)
Yield strength (0.5% ext.)>= 427 MPa (62 ksi)
Elongation (2 in.)>= 14%
Hardnessabout 223 HB (typical)
Density7.83 g/cm3
Melting range885-923 C
Electrical conductivity8% IACS
Compression deformation limit>= 380 MPa (55 ksi)

Mechanical values are standard minima; hardness is typical.

Typical Applications

heavy-duty gearsworm wheelsvalve stems and nutsbridge pinshydraulic cylinder partscams and gibswear ringsslow-speed heavy-load bearings

Heavy-duty gears and worm wheels, valve stems and nuts, bridge pins, hydraulic cylinder parts, cams, gibs, wear rings, large slow-speed bearings, marine hardware and structural machine parts.

Grade Overview

C86300 is a high-strength yellow brass - the trade calls it manganese bronze, though metallurgically it is a brass. Copper 60-66%, zinc 22-28%, aluminum 5-7.5%, manganese 2.5-5% and iron 2-4% produce the highest strength of the standard cast copper alloys: minimum tensile strength around 758 MPa, yield around 427 MPa and hardness around 223 HB. It is used where a copper-base part must carry a very heavy load at low speed and still resist wear and corrosion.

Typical duty is slow-turning and heavily loaded: large gears, worm wheels, valve stems and nuts, bridge pins, hydraulic cylinder parts, cams, wear rings and marine hardware. It is not a bearing alloy in the sense of C93200 - it needs reliable lubrication - but under high load and good lubrication it outperforms the tin bronzes.

Standards and Equivalents

ASTM B505 covers continuous-cast bar and ASTM B271 centrifugal castings; QQ-C-523 and MIL-C-11866 are older call-outs still encountered. The Chinese near-equivalent is ZCuZn25Al6Fe3Mn3 in GB/T 1176, also listed in ISO 1338, and EN 1982 has CuZn25Al6Fe3Mn3 (CC762S). The high zinc content means that aluminum and manganese control strongly affects strength and ductility, so chemistry and mechanical results must both be certified.

UNSC86300
Common namemanganese bronze / high-strength yellow brass
ASTMB505 (continuous) / B271 (centrifugal)
Federal / militaryQQ-C-523; MIL-C-11866
ChinaZCuZn25Al6Fe3Mn3 (GB/T 1176, ISO 1338)
EuropeCuZn25Al6Fe3Mn3 / CC762S (EN 1982)

Equivalent grades are close in composition and duty, not identical. Order and certify to the standard named on the drawing.

How to Specify C86300 on a Drawing

Selecting C86300

C86300 is the right choice when a copper alloy part must carry very high load at low speed - gears, pins, nuts and heavy bushings with good lubrication. For seawater and corrosion-critical duty, aluminum bronze C95400 or nickel aluminum bronze is safer, because the high zinc content of C86300 carries a dezincification risk in stagnant or aggressive water. For general bearings, C93200 is cheaper and more forgiving.

Casting and Machining Notes

C86300 machines at about 80% of free-cutting brass, but its strength makes it less forgiving of poor tooling and weak setups. In casting, aluminum and manganese must be controlled closely; the alloy is prone to hard spots and segregation if pouring and cooling are not managed. It is not normally welded; brazing is possible but is not a structural repair. In seawater service, protect it from stagnant conditions and from galvanic coupling with more noble metals.

Frequently asked questions about C86300

Is C86300 a bronze or a brass?

Metallurgically it is a brass - a copper-zinc alloy with aluminum, manganese and iron additions. "Manganese bronze" is the traditional trade name and is used throughout US catalogues, so both names refer to the same UNS C86300 alloy.

C86300 or C95400 for a heavy bearing?

C86300 is much stronger and harder, and is the better choice for very high load at low speed with reliable lubrication. C95400 aluminum bronze is more corrosion-resistant, weldable and more forgiving in seawater. Choose on the combination of load, speed, lubrication and environment.

Can C86300 be welded?

Not normally. It is a high-strength brass and fusion welding is not recommended; repairs are made by replacement or agreed with the foundry before casting. Brazing is possible but should not be treated as a structural repair.

Is C86300 suitable for seawater?

It is used in marine hardware and has useful corrosion resistance, but the 22-28% zinc content means dezincification is a real risk in stagnant or polluted seawater. For critical seawater parts, specify a nickel aluminum bronze such as C95500 or C95800 instead, and avoid galvanic coupling with steel.

Data compiled from published ASTM B505/B505M, B584 and B148 limits and from mill specification sheets; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related grades

C95400 · ZCuZn25Al6Fe3Mn3 (GB/T 1176) · C93200  |  All grades in the library

← Back to Alloy Grades