Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

QSn7-0.2

7-0.2 Phosphor Bronze (Wrought, Higher Tin)  |  Wrought Copper Alloy  |  GB/T 5231  |  UNS C52000

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Sn6.0~8.0
P0.10~0.25
CuBalance

Mechanical & Physical Properties

Tensile strength≥310 MPa
Elongation≥45%
Density8.8 g/cm³

Typical Applications

bearingsbushingsworm wheelsspringsspring leaves

Grade Overview

A wrought phosphor bronze with slightly more tin than the 6.5-0.1 grade, used for bearings, bushings, worm wheels, springs and spring leaves subject to moderate friction. The higher tin content brings better strength, elasticity and wear resistance while ductility stays good, and corrosion resistance and weldability are also sound: annealed tensile strength is at least 310 MPa with elongation of over 45%, so cold press forming is straightforward. In the hard temper strength is higher and forming correspondingly harder. It is commonly used for moderately loaded parts that see friction and wear. Select the supply temper according to the amount of forming required and strengthen after forming, and control heat input during welding so the heat-affected zone does not lose properties. Where elasticity is the main requirement, a higher-elasticity phosphor bronze may be a better choice. For bearing and bushing work it is chosen where friction is moderate and lubrication can be maintained, while its good ductility keeps forming and assembly straightforward.

Selecting QSn7-0.2

Choose QSn7-0.2 when you want a wrought phosphor bronze with a little more tin than QSn6.5-0.1 — for bearings, bushings, worm wheels, springs and spring leaves under moderate friction and wear. The extra tin brings better strength, elasticity and wear resistance while ductility stays good, and corrosion resistance and weldability remain sound: annealed tensile strength is at least 310 MPa with elongation above 45%, so cold press forming is straightforward. In the hard temper strength is higher and forming correspondingly harder. Where maximum spring strength is the goal, QSn6.5-0.1 or QBe2 suits better. Where bearing duty is heavier and lubrication intermittent, a cast bearing bronze such as ZCuSn10P1 or ZCuPb10Sn10 is more appropriate. Where the part is plain corrosion-resistant hardware, a brass may be cheaper.

Working with QSn7-0.2

QSn7-0.2 is selected by temper: choose the supply condition according to the amount of forming required, and strengthen after forming, because the alloy is not strengthened by heat treatment. Cold press forming is straightforward in the annealed condition, with elongation above 45%. Welding is possible; control heat input so the heat-affected zone does not lose properties, and stress-relieve cold-worked parts that will carry sustained load in ammonia-bearing or damp conditions. For bearing and bushing work, ensure lubrication can be maintained, since the alloy is chosen where friction is moderate. Because the tin content is slightly higher than the 6.5-0.1 grade, the working range shifts a little and heavier reductions should be taken in stages.

Frequently asked questions about QSn7-0.2

How does QSn7-0.2 compare with QSn6.5-0.1?

QSn7-0.2 carries slightly more tin, which improves strength, elasticity and wear resistance while keeping good ductility — annealed tensile strength is at least 310 MPa with elongation above 45%. QSn6.5-0.1 has a high-strength hard temper of above 540 MPa and a slightly wider margin of formability. Choose between them by whether wear resistance or spring strength and formability dominate.

Where is QSn7-0.2 used?

Typical uses are bearings, bushings, worm wheels, springs and spring leaves that see moderate friction. Its combination of good ductility, wear resistance and corrosion resistance suits parts that must be formed and then run with lubrication. For heavier bearing loads or poor lubrication, a cast bearing bronze is a better choice.

Does QSn7-0.2 need heat treatment?

No. It is not hardenable by heat treatment, so strength comes from cold work and from the temper of the strip, wire or bar you buy. Choose the supply temper to match the forming, do the forming, then strengthen by cold work. Low-temperature annealing can relieve stress or adjust properties, but it will not raise strength.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

T2 · BFe10-1-1 · BFe30-1-1  |  All 52 grades in the library

← Back to Alloy Grades