Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

BFe10-1-1

BFe10-1-1 Cupronickel (B10, 90/10 Cu-Ni)  |  Wrought Copper Alloy  |  GB/T 5231  |  UNS C70600

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Ni+Co9.0~11.0
Fe1.0~1.5
Mn0.5~1.0
CuBalance

Mechanical & Physical Properties

Tensile strength≥295 MPa
Elongation≥25%
Density8.9 g/cm³
Thermal conductivity40 W/(m·K)

Typical Applications

condenser tubesheat-exchanger tubesseawater pipingmarine pipe fittings

Grade Overview

A wrought iron-bearing cupronickel, known as B10, with about 10% nickel, used for condenser tubes, heat-exchanger tubes, seawater piping and marine pipe fittings. Nickel raises resistance to flowing seawater and impingement corrosion, iron improves corrosion resistance and manganese optimises processing behaviour; thermal conductivity is about 40 W/(m·K), weldability is good, and tensile strength is at least 295 MPa with elongation of at least 25%. It is the mainstay material for condensers and heat-exchanger tubing. Strength and hardness are only moderate, and resistance to ammonia attack is below that of higher-nickel grades. It is widely used in ships, thermal power plant and seawater desalination equipment; avoid high-velocity sand-bearing water in service, and watch for ammonia and sulphide attack in the medium. Tube is normally supplied annealed for bending and expanding, and the alloy tolerates the moderate flow velocities of condensers and heat exchangers; where the water is unusually aggressive or the temperature higher, the 30% nickel grade is the safer choice.

Selecting BFe10-1-1

Choose BFe10-1-1 when you need seawater-cooled condenser or heat-exchanger tubing, piping or marine fittings at moderate flow velocity and moderate temperature, and cost matters. Its roughly 10% nickel, with iron and manganese, gives good resistance to flowing seawater and impingement corrosion while keeping thermal conductivity around 40 W/(m·K), so heat-transfer surfaces stay compact; it welds well, and with tensile strength of at least 295 MPa and elongation of at least 25% it suits tube that must be bent and expanded. Where the water is more aggressive — higher temperature, higher pressure, severe impingement, or ammonia and sulphides in the medium — step up to BFe30-1-1 (B30), which has far more nickel and better tolerance. For freshwater or non-corrosive pipework, a brass such as H62 or HSn62-1 costs less. Do not use B10 for high-velocity sand-bearing water, and check the mill certificate against the standard on the drawing.

Working with BFe10-1-1

BFe10-1-1 is normally supplied as annealed tube and is worked by bending, expanding and flaring; keep cold reduction modest and anneal between forming stages, because the alloy work-hardens. For welding, use matching cupronickel filler and low heat input, clean the joint, and avoid overheating that can promote hot cracking; the iron and manganese additions help weldability but do not remove the need for good fit-up. Melting and casting of fittings, if that route is used, need clean charge material and protection against oxidation. In service, keep flow velocity within condenser and heat-exchanger practice and avoid stagnant, ammonia-bearing or sulphide-bearing water. Do not couple the tube directly to bare steel without an insulating sleeve, to limit galvanic attack, and allow for the alloy's thermal expansion against steel supports.

Frequently asked questions about BFe10-1-1

Is BFe10-1-1 the same as C70600?

Yes. BFe10-1-1 is the Chinese GB/T 5231 designation for the 90/10 cupronickel commonly known as C70600, with about 10% nickel plus iron and manganese. The two are quoted interchangeably in seawater and heat-exchanger work, but the mill certificate should be checked against the standard named on the drawing, since tolerances and property limits can differ.

Why does BFe10-1-1 contain iron and manganese?

Iron is the main reason the alloy resists flowing seawater and impingement corrosion; without it a 90/10 cupronickel is far less durable in condenser service. Manganese is added to improve processing behaviour and to keep the iron in a useful form in the structure. The published range is 1.0-1.5% Fe and 0.5-1.0% Mn.

When should I use B30 instead of B10?

Move to BFe30-1-1 where temperatures and pressures are higher, flow velocities or impingement are severe, or the medium carries ammonia or sulphides that attack lower-nickel cupronickel. B10 is the economical choice for normal condenser and heat-exchanger tube; B30 buys longer life under harsher seawater conditions, at higher cost and lower thermal conductivity.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

BFe30-1-1 · BZn15-20 · H59  |  All 52 grades in the library

← Back to Alloy Grades