Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

H59

H59 Brass (59% Cu, Two-Phase, Wrought)  |  Wrought Copper Alloy  |  GB/T 5231  |  UNS C28000

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Cu57.0~60.0
ZnBalance

Mechanical & Physical Properties

Tensile strength≥294 MPa
Elongation≥25%
Density8.4 g/cm³

Typical Applications

structural partshardwarestampingsconnectors

Grade Overview

A lower-copper two-phase wrought brass used for structural parts, hardware, stampings and connectors. With about 59% copper the structure contains both alpha and beta phases, so strength and hardness are high with acceptable ductility and the price is the lowest of the common brasses; it still accepts pressure working when hot, with tensile strength of at least 294 MPa and elongation of at least 25%. Cold-forming ductility is below that of single-phase brass, work hardening is rapid and corrosion resistance is only average, with a pronounced tendency to dezincification. Use it for ordinary structural and hardware stampings under moderate load. Because the ductility reserve is limited, control deformation per pass and anneal between stages in cold forming, and be cautious or apply stress relief where corrosive media and residual tensile stress combine. Hot forging and extrusion are the natural processes for this grade, and parts are usually finished by machining or light cold forming rather than deep drawing.

Selecting H59

Choose H59 when cost is the main driver and the part is a structural stamping, hardware item, connector or fitting that will be hot worked or lightly cold formed rather than deep drawn. With about 59% copper the structure is two-phase, giving higher strength and hardness than single-phase brass and costing less than the higher-copper brasses; tensile strength is at least 294 MPa and elongation at least 25%. Its limits are real: cold-forming ductility is lower than H62's, it work-hardens rapidly, corrosion resistance is only average, and it dezincifies readily. Where parts must be deep drawn, choose H62 instead. Where seawater or aggressive chloride service is involved, choose HSn62-1 for better corrosion resistance. Where higher strength is required from a cast brass, consider ZCuZn25Al6Fe3Mn3 or the cast manganese brass ZCuZn38Mn2Pb2.

Working with H59

H59 is usually hot forged or extruded; those are its natural processes. If you cold form it, control the reduction per pass and anneal between stages, because its ductility reserve is limited and it work-hardens quickly. Machining is straightforward and gives a good finish, so many parts combine hot or warm forming with a machining operation. Where a part is cold worked and then used under load in a damp or chloride-bearing environment, stress-relieve it to reduce the risk of stress-corrosion cracking, and keep it away from ammonia. Soldering and brazing are normally used for joints rather than welding. Its average corrosion resistance means it should not be left unprotected in aggressive media.

Frequently asked questions about H59

What is the difference between H59 and H62?

H62 is a near-single-phase brass with about 62% copper, and it takes cold forming and deep drawing much better. H59, at about 59% copper, is two-phase, so it is stronger and harder and costs less but is less ductile in cold forming and more prone to dezincification. Use H62 for forming, H59 for hot-worked structural and hardware parts.

Can H59 be welded?

It is usually joined by soldering or brazing rather than welding. Welding zinc-bearing brass is difficult because zinc vaporises and the weld can be porous and weak, and heat can cause dezincification near the joint. Design the part for mechanical fastening, soldering or brazing, and if welding is unavoidable, use a suitable filler and control heat input closely.

How do I avoid cracking in cold-formed H59 parts?

Limit the deformation per pass and anneal between stages, because the two-phase structure work-hardens quickly and its cold-forming ductility is limited. After the final cold operation, stress-relieve parts that will see sustained tensile stress in damp or chloride-bearing conditions, which reduces the risk of stress-corrosion cracking. Keeping the part out of ammonia-bearing environments also helps.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

H62 · HSn62-1 · QAl10-4-4  |  All 52 grades in the library

← Back to Alloy Grades