Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

HSn62-1

HSn62-1 Tin Brass (Naval Brass)  |  Wrought Copper Alloy  |  GB/T 5231  |  UNS C46400

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Cu61.0~63.0
Sn0.7~1.1
ZnBalance

Mechanical & Physical Properties

Tensile strength≥380 MPa
Hardness50~95 HBW
Density8.45 g/cm³

Typical Applications

marine partsseawater pipe fittingsboltscondenser tubesheat exchangers

Grade Overview

A tin brass made by adding about 1% tin to 62 brass, known as naval brass because its seawater corrosion resistance is markedly improved; it is used for marine parts, seawater pipe fittings, bolts, condenser tubes and heat exchangers. The tin addition substantially improves resistance to seawater while strength, workability and weldability remain good: tensile strength at least 380 MPa and hardness about 50-95 HBW. The corrosion benefit applies mainly to seawater, and the tendency to dezincification remains, so high temperature or high flow velocity still demands care. It is widely used for shipboard and seawater-contact pipe fittings and bolts. Control residual stress after cold working and stress-relieve the parts, and avoid service in ammonia-bearing environments. It is normally supplied as rod, bar and tube for machining, and it cuts freely to a good finish; the grade is a standard choice for marine fasteners and for condenser and heat-exchanger tube plates.

Selecting HSn62-1

Choose HSn62-1 when you need a wrought brass for marine and seawater-contact parts — pipe fittings, bolts, fasteners, condenser and heat-exchanger components — where plain brass would dezincify too readily. Adding about 1% tin to 62% brass markedly improves resistance to seawater while keeping good strength, workability and weldability; tensile strength is at least 380 MPa and hardness is about 50-95 HBW. That makes it an economical step up from H62 for seawater duty, and it machines freely to a good finish. Where service is hotter, faster or more aggressive — high velocity, impingement, ammonia or sulphides — cupronickel BFe10-1-1 or BFe30-1-1 is the better choice for tube and severe service. Where cost dominates and the medium is not aggressive, H62 or H59 will do.

Working with HSn62-1

HSn62-1 is normally supplied as rod, bar and tube for machining, and it cuts freely to a good finish; watch residual stress after cold working and stress-relieve parts that will see sustained tensile load in seawater, because dezincification and stress-corrosion cracking still apply. It is weldable and brazes well, but control heat input to limit zinc loss and grain growth near the joint. For pipe fittings and bolts, specify the finished temper and control the process so dimensions stay stable. Avoid service in ammonia-bearing media, and do not assume the tin addition protects against high temperature or high flow velocity — the corrosion benefit is mainly for seawater under ordinary conditions.

Frequently asked questions about HSn62-1

Why is HSn62-1 called naval brass?

About 1% tin is added to a 62% copper brass, and that modest addition markedly improves resistance to seawater, which made the alloy a standard for shipboard fittings, condenser plates and marine fasteners. Strength, workability and weldability remain good, and it machines well. It is still a brass, so dezincification and stress-corrosion cracking remain risks under severe conditions.

Is HSn62-1 good enough for seawater tube?

It is used for marine parts, seawater pipe fittings and condenser tube plates, and it resists seawater far better than plain brass. But it remains a tin brass and can dezincify at high temperature or high flow velocity, so where tubes see fast, hot, impingement-heavy or ammonia-bearing seawater, cupronickel BFe10-1-1 or BFe30-1-1 is the more durable choice.

How does HSn62-1 compare with H62?

Both are wrought brasses of about 62% copper, and H62 works and forms well and costs less. HSn62-1 adds about 1% tin, which improves seawater corrosion resistance and makes it the standard choice for marine fittings, bolts and condenser components. For non-aggressive media H62 is adequate; for seawater contact HSn62-1 is worth the extra cost.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

QAl10-4-4 · QAl10-5-5 · QAl9-4  |  All 52 grades in the library

← Back to Alloy Grades