Chemical Composition (%)
| Al | 9.5~11.0 |
|---|---|
| Fe | 3.5~5.5 |
| Ni | 3.5~5.5 |
| Cu | Balance |
Mechanical & Physical Properties
| Tensile strength | ≥690 MPa |
|---|---|
| Elongation | ≥5% |
| Hardness | 170~240 HBW |
| Density | 7.5 g/cm³ |
Typical Applications
Grade Overview
A wrought nickel-iron aluminum bronze, classed as a high-strength heat-resistant copper alloy, used for bushings, flanges, gears, nuts and wear- and corrosion-resistant parts. Nickel and iron strengthen together and refine the structure, giving high strength and hardness - tensile strength of at least 690 MPa and hardness of about 170-240 HBW - and the alloy responds to heat treatment, keeps useful mechanical properties up to about 400 °C, and has good anti-friction behaviour and seawater corrosion resistance. The weak points are poor brazability, only fair machinability and comparatively limited ductility. Specify it for high-strength, corrosion-resistant and high-temperature wear parts; plan a suitable heat treatment and machining sequence, avoid galvanic coupling with dissimilar metals in corrosive media, and control temperature and deformation in hot forming. It is one of the strongest wrought copper alloys, so it is chosen where a compact section has to carry heavy load and resist corrosion at the same time; the limited ductility means sharp notches and tight bend radii should be avoided.
Selecting QAl10-4-4
Choose QAl10-4-4 where a wrought part must carry heavy load and resist corrosion at the same time — bushings, flanges, gears, nuts and wear parts in pumps, valves and marine or industrial service. It is a high-strength wrought copper alloy: nickel and iron strengthen together and refine the structure, giving tensile strength of at least 690 MPa and hardness around 170-240 HBW, and it responds to heat treatment and keeps useful mechanical properties up to about 400 °C. The price is limited ductility and only fair machinability, with poor brazability and sensitivity to notches, so tight bend radii and sharp corners should be avoided. Where less strength is enough, QAl9-4 is cheaper and easier to work. Where the part is cast to shape, ZCuAl10Fe3 or ZCuAl10Fe3Mn2 are the casting counterparts. Where corrosion rather than strength dominates, cupronickel or ZCuAl9Fe4Ni4Mn2 may fit better.
Working with QAl10-4-4
QAl10-4-4 is usually hot worked and heat treated; control temperature and deformation during hot forming and plan the heat treatment and machining sequence, because the alloy responds to treatment and the required properties come from that schedule. Machining needs sharp tooling and rigid setups — aluminum bronze work-hardens at the surface if the tool rubs. Brazing is poor, so joints are normally welded or mechanical; where it works with steel, allow for differences in thermal expansion and conductivity. Avoid galvanic coupling with dissimilar metals in corrosive media. Because ductility is limited, avoid sharp notches in design and do not expect tight bend radii. Verify the heat-treated condition against the drawing before final machining.
Frequently asked questions about QAl10-4-4
What does QAl10-4-4 do better than QAl9-4?
The nickel addition raises strength and high-temperature capability: QAl10-4-4 reaches at least 690 MPa tensile strength with hardness of about 170-240 HBW and keeps useful properties up to about 400 °C, while QAl9-4 reaches at least 540 MPa. The cost is lower ductility and harder machining. Choose QAl10-4-4 for heavily loaded, hot or wear-critical parts, and QAl9-4 where cost and workability matter more.
Can QAl10-4-4 be cast instead?
The grade itself is a wrought alloy supplied as bar, forging stock and similar forms. Where a part is cast to shape, the casting equivalents are ZCuAl10Fe3 and the manganese-bearing ZCuAl10Fe3Mn2, which have similar aluminum and iron levels but are formulated and heat treated for casting. Select between them according to whether the part is machined from wrought stock or poured as a casting.
How should QAl10-4-4 be machined?
Use sharp tooling, rigid setups and positive feeds, and keep the tool cutting rather than rubbing: aluminum bronze work-hardens at the surface and a dull tool makes the next cut harder. Expect only fair machinability, and do not confuse it with free-cutting brass. Because ductility is limited, avoid sharp notches and heavy interrupted cuts, and plan the machining sequence around any required heat treatment.
Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.