Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

QAl9-4

9-4 Iron Aluminum Bronze (Wrought)  |  Wrought Copper Alloy  |  GB/T 5231

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Al8.0~10.0
Fe2.0~4.0
CuBalance

Mechanical & Physical Properties

Tensile strength≥540 MPa
Density≈7.5 g/cm³

Typical Applications

bushingswear partsvalve partsstructural components

Grade Overview

A simple iron-bearing wrought aluminum bronze used for bushings, wear parts, valve parts and structural components. Iron refines the grain and forms hard particles, giving high strength with good anti-friction behaviour and corrosion resistance, and hot pressure working is sound; the alloy can be electric- and gas-welded, has tensile strength of at least 540 MPa and a density of about 7.5 g/cm³. It is often used to replace high-tin wear-resistant bronze and reduce cost. Brazing is poor, cold-forming ductility is only fair, and when it works with steel the differences in thermal expansion and conductivity must be allowed for. Choose it for wear- and corrosion-resistant structural parts; control temperature during welding and hot working to avoid overheating and embrittlement, design the fit and thermal-expansion clearance correctly in steel assemblies, and remember that its hot-working range is narrow. Where machining matters, aluminum bronze needs sharp tooling and rigid setups, and its resistance to seawater and most industrial atmospheres makes it useful in pump and valve components.

Selecting QAl9-4

Choose QAl9-4 where you want aluminum bronze strength, wear resistance and corrosion resistance in a wrought part without the cost and processing difficulty of the nickel-bearing QAl10-4-4 — bushings, wear parts, valve parts and structural components. Iron refines the grain and forms hard particles, giving tensile strength of at least 540 MPa with good anti-friction behaviour, and the alloy can be electric- and gas-welded and hot pressure worked. It is often used to replace high-tin wear-resistant bronze and cut cost. Its limits are poor brazing, only fair cold-forming ductility and a narrow hot-working range; when it works against steel, allow for differences in thermal expansion and conductivity. Where the load and temperature are higher, step up to QAl10-4-4. Where the part is cast to shape, ZCuAl10Fe3 or ZCuAl9Mn2 are the casting options. Where elasticity rather than strength is needed, phosphor bronze is better.

Working with QAl9-4

QAl9-4 is hot worked, or used as cast-and-machined stock; keep its narrow hot-working range in mind and avoid overheating and embrittlement. Welding is possible by electric and gas methods, but control heat input and preheat sensibly, since coarse grain and hard phases can form if the part is held hot too long. Machining needs sharp tooling and rigid setups, as the alloy work-hardens at the surface. Brazing is poor, so use welding or mechanical joints. In steel assemblies, design the fit and thermal-expansion clearance so differential expansion does not overload the bronze, and avoid galvanic coupling with dissimilar metals in corrosive service. Inspect for the brittle phases that an incorrect thermal cycle can produce.

Frequently asked questions about QAl9-4

How does QAl9-4 differ from QAl10-4-4?

QAl9-4 contains iron but no deliberate nickel, giving at least 540 MPa tensile strength with good wear and corrosion resistance at lower cost and with easier working. QAl10-4-4 adds nickel and iron and reaches at least 690 MPa with higher hardness and useful strength to about 400 °C, at the cost of ductility and machinability. Use QAl9-4 for general wear and corrosion parts, QAl10-4-4 for heavier and hotter duty.

Can QAl9-4 replace tin bronze?

It is often chosen to replace high-tin wear-resistant bronze while reducing cost, because its strength, hardness and wear resistance are useful and it resists seawater and most industrial atmospheres. It is not simply interchangeable: aluminum bronze needs sharper tooling, tolerates less cold forming, and has different thermal expansion and conductivity from tin bronze, so fits and processes must be reviewed.

Is QAl9-4 weldable?

Yes, the alloy can be electric- and gas-welded. The welding procedure matters, though: control heat input to avoid overheating and embrittlement, and keep the narrow hot-working range in mind. Brazing, by contrast, is poor, so welded or mechanical joints are preferred. Where the part works with steel, account for the different thermal expansion in the design.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

QBe2 · QSn4-3 · QSn6.5-0.1  |  All 52 grades in the library

← Back to Alloy Grades