Chemical Composition (%)
| Sn | 3.5~4.5 |
|---|---|
| Zn | 2.7~3.3 |
| Cu | Balance |
Mechanical & Physical Properties
| Density | 8.8 g/cm³ |
|---|---|
| Melting point (liquidus) | 1046 ℃ |
Typical Applications
Grade Overview
A wrought tin-zinc bronze used for springs, elastic elements, corrosion-resistant parts, non-magnetic parts and bushings. The zinc addition improves casting and pressure-working behaviour; the alloy has fairly high wear resistance and elasticity, is non-magnetic, resists atmospheric and seawater corrosion, and both hot and cold working are easy, with a liquidus of about 1046 °C. It cannot be strengthened by heat treatment, so strength comes mainly from cold work and the soft temper is only of medium strength; properties therefore depend on the amount of reduction applied. Specify it for springs, corrosion-resistant parts and non-magnetic components; arrange the amount of cold work in the direction of loading, avoid long service at high temperature that would cause stress relaxation, and remember the stress-corrosion risk of zinc-bearing alloys in ammonia environments. Because the alloy is zinc-bearing, parts that are cold formed and then stressed should be stress-relieved, and service temperatures kept low enough to avoid relaxation of the spring properties.
Selecting QSn4-3
Choose QSn4-3 where you need a wrought bronze for springs, elastic elements, corrosion-resistant and non-magnetic parts or bushings, and the forming is straightforward. The zinc addition improves casting and pressure-working behaviour, so it works both hot and cold, and it resists atmospheric and seawater corrosion while its liquidus is around 1046 °C. It cannot be strengthened by heat treatment, so strength and elasticity come from cold work, and the soft temper is only of medium strength; that means the supply temper and the amount of cold reduction must be planned. Where higher strength and elasticity are needed, step up to QSn6.5-0.1 or QSn7-0.2. Where strength must come from heat treatment rather than cold work, QBe2 or C96900 are the alternatives, at much higher cost. Where seawater tube or severe corrosion is involved, cupronickel BFe10-1-1 is the better fit.
Working with QSn4-3
QSn4-3 cannot be strengthened by heat treatment; arrange the amount of cold work in the direction of loading so the finished part has the properties you designed for. It works hot and cold and is easy to form, but because it contains zinc, parts that are cold worked and then stressed should be stress-relieved, and service temperature should be kept low enough to avoid relaxation of the spring properties. Melting and casting, if applicable, are straightforward, with a liquidus around 1046 °C. Keep the alloy out of ammonia-bearing environments, where zinc-bearing copper alloys are prone to stress-corrosion cracking, and control heat input if it is welded. Specify the temper of the strip, wire or bar together with the forming sequence, since properties depend on it.
Frequently asked questions about QSn4-3
How strong is QSn4-3?
Its strength depends heavily on temper. The alloy cannot be strengthened by heat treatment, so properties come from cold work, and the soft temper is only of medium strength. That is why the drawing should specify the temper and the forming sequence, and why the amount of cold reduction should be arranged in the direction of loading. Where higher spring strength is needed, QSn6.5-0.1 or QSn7-0.2 is the next step.
What is the liquidus of QSn4-3?
The alloy's liquidus is about 1046 °C. That figure matters mainly for casting and for setting hot-working temperatures, where it helps define the working window. Since the alloy also contains about 2.7-3.3% zinc alongside 3.5-4.5% tin, it is a tin-zinc bronze rather than a plain phosphor bronze, and it works both hot and cold.
Is QSn4-3 good for marine service?
It resists atmospheric and seawater corrosion, so it has been used for corrosion-resistant and non-magnetic parts, but it is a moderate-strength bronze and should not be chosen for tube or severe impingement duty. For seawater tube and heat-exchange service, cupronickel BFe10-1-1 is the established choice, and BFe30-1-1 is better still where conditions are harsh.
Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.
Related wrought copper alloy grades
QSn6.5-0.1 · QSn6.5-0.4 · QSn7-0.2 | All 52 grades in the library