Chemical Composition (%)
| Cu | 60.5~63.5 |
|---|---|
| Zn | Balance |
Mechanical & Physical Properties
| Tensile strength | ≥300 MPa (soft temper) |
|---|---|
| Density | 8.43 g/cm³ |
Typical Applications
Grade Overview
One of the most general-purpose wrought brasses, with about 62% copper, widely used for tube, rod, strip, hardware and machine parts. Strength, ductility, workability and corrosion resistance are well balanced and the price is low; hot and cold working and welding are all good, and soft-temper tensile strength is at least 300 MPa with a density of about 8.43 g/cm³. Dezincification and stress-corrosion cracking are its principal weaknesses: under sustained tensile stress in chloride-bearing or damp conditions it can crack, and deep-drawn parts may tear. Use it for general-purpose tube, rod, sheet, strip and hardware. Stress-relieve deep-drawn or cold-worked parts, and avoid long-term tensile stress in ammonia-bearing and seawater environments. It is easy to join by soldering, brazing and welding and is supplied in many tempers, from soft for forming to hard for strength. Because properties depend on the temper, the required condition should be specified with the drawing, and formed parts should be annealed or stress-relieved before going into corrosive service.
Selecting H62
Choose H62 when you need a general-purpose wrought brass that combines good strength, ductility and working properties at low cost — tube, rod, sheet, strip, hardware and machined parts. It has about 62% copper, works both hot and cold, is easy to solder, braze and weld, and soft-temper tensile strength is at least 300 MPa. Its weaknesses are dezincification and stress-corrosion cracking: under sustained tensile stress in chloride-bearing or damp conditions it can crack, and deep-drawn parts may tear. Where the part must resist seawater better, choose HSn62-1. Where cost is the priority and forming demands are light, H59 will do. Where higher spring properties are needed, go to BZn15-20 or a phosphor bronze such as QSn6.5-0.1. Where strength and wear resistance matter more, consider aluminum bronze QAl9-4 or a cast grade such as ZCuAl10Fe3.
Working with H62
H62 is supplied in many tempers, from soft for forming to hard for strength, so the required condition should be named on the drawing and the forming sequence planned around it. Deep-drawn and cold-worked parts should be stress-relieved before going into corrosive service, to lower the risk of stress-corrosion cracking. Joining is easy by soldering, brazing and welding; where brazing is used, avoid overheating and excessive zinc loss. Keep parts out of ammonia-bearing environments and away from long-term tensile stress in chloride service. For machined parts, free-cutting tempers give a better finish; if the part must also be formed, do the forming first and machine afterwards, so residual stress and distortion are easier to control.
Frequently asked questions about H62
What temper should I order H62 in?
Name the temper with the drawing, because H62 is supplied soft, half-hard, hard and in other conditions, and strength depends on it. Soft temper gives at least 300 MPa tensile strength and good formability, and is the right starting point for deep drawing; harder tempers give higher strength but less ductility. The forming sequence and the ordering condition should be agreed together.
Why does H62 crack in service?
Two mechanisms are common: dezincification, where zinc is leached from the alloy in chloride-bearing or damp conditions, and stress-corrosion cracking under sustained tensile stress together with ammonia or moisture. Deep-drawn parts are especially exposed, because forming leaves residual stress. Stress-relieve cold-worked parts and avoid long-term tensile stress in those environments.
Is H62 suitable for marine fittings?
It is a general-purpose brass, not a marine grade. It resists some seawater attack but dezincifies, so it is not the right choice for sustained seawater or high-velocity service. For marine and seawater fittings, HSn62-1 tin brass is the better wrought option, and cupronickel BFe10-1-1 or BFe30-1-1 is better still where tubes, heat exchange or severe conditions are involved.
Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.
Related wrought copper alloy grades
HSn62-1 · QAl10-4-4 · QAl10-5-5 | All 52 grades in the library