Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Wrought Copper Alloy

BFe30-1-1

BFe30-1-1 Cupronickel (B30, 70/30 Cu-Ni)  |  Wrought Copper Alloy  |  GB/T 5231  |  UNS C71500

This grade is available on request. Send a drawing, sample or old part — we reply within 1 business day.  Request a quote

Chemical Composition (%)

Ni+Co29.0~33.0
Fe0.5~1.0
Mn0.5~1.2
CuBalance

Mechanical & Physical Properties

Tensile strength≥490 MPa (bar)
Density8.9 g/cm³

Typical Applications

condensersthermostatsseawater heat exchangershigh-pressure pipe fittings

Grade Overview

A wrought iron-bearing cupronickel, known as B30, with about 30% nickel, used for condensers, thermostats, seawater heat exchangers and high-pressure pipe fittings. The higher nickel content makes seawater resistance, tolerance of high temperature and pressure and impingement-corrosion resistance all stronger than B10, with higher strength and toughness - bar tensile strength is at least 490 MPa - and a longer life in demanding seawater service. The trade-offs are slightly lower thermal conductivity, a higher price and poorer machinability, together with a pronounced tendency to work harden. Specify it for heat-exchange and piping systems at high temperature and pressure or in severe corrosion conditions; plan intermediate annealing during processing, control heat input when welding, and account for the effects of conductivity and thermal expansion in the design. The combination of strength and seawater resistance suits thin-wall tubing and fittings that must hold pressure, and allowance should be made for its lower thermal conductivity when heat transfer surfaces are sized.

Selecting BFe30-1-1

Choose BFe30-1-1 where a seawater heat-exchange or piping system runs at higher temperature and pressure than B10 can tolerate, where impingement corrosion is severe, or where the water carries ammonia or sulphides. About 30% nickel, with iron and manganese, gives markedly better seawater resistance, temperature tolerance and impingement-corrosion resistance than BFe10-1-1, and bar tensile strength is at least 490 MPa, so thin-wall tube and fittings can hold pressure. The trade-offs are lower thermal conductivity, higher cost and a pronounced work-hardening tendency, which affect heat-transfer sizing and forming. For ordinary condenser duty at moderate velocity, BFe10-1-1 is usually enough and cheaper. For non-seawater work, a tin brass such as HSn62-1 or a plain brass like H62 will do at lower cost, but neither matches cupronickel in hot, fast or ammonia-bearing seawater.

Working with BFe30-1-1

Plan intermediate annealing when bending, expanding or cold forming BFe30-1-1, because work hardening is pronounced and cracks appear quickly if reduction per pass is too high. Weld with matching 70/30 cupronickel filler and controlled heat input; purge the back of tube joints where possible, since copper-nickel welds are sensitive to oxidation and porosity. Keep the melt clean and well deoxidised if fittings are cast. In service, allow for lower thermal conductivity when sizing heat-transfer surfaces, and use insulating sleeves at steel connections to limit galvanic corrosion. Keep the medium free of ammonia and sulphides, avoid stagnant seawater, and account for the alloy's different expansion from steel in tube supports and rolled joints.

Frequently asked questions about BFe30-1-1

What does BFe30-1-1 offer over BFe10-1-1?

The higher nickel content, about 29-33%, gives better resistance to seawater, higher temperature and pressure capability, and better impingement-corrosion performance, with bar tensile strength of at least 490 MPa. The cost is slightly lower thermal conductivity, a higher price and harder machining and forming. It is the grade for demanding seawater heat exchangers, condensers and high-pressure fittings.

Can BFe30-1-1 be welded?

Yes, it is weldable, but heat input must be controlled and the joint kept clean; matching 70/30 cupronickel filler is the usual choice, and back purging helps on tube. Because the alloy work-hardens strongly, weld preparations should be planned with the forming and annealing sequence, and post-weld cleaning should avoid iron contamination that can start corrosion.

Why is BFe30-1-1 used for thermostats and high-pressure fittings?

Its combination of strength, toughness and seawater resistance lets thin sections carry pressure without corroding through as fast as lower-nickel grades. That is why it appears in thermostats, seawater heat exchangers and high-pressure pipe fittings, where a leak is costly. The design should account for its lower thermal conductivity and different expansion from steel.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related wrought copper alloy grades

BZn15-20 · H59 · H62  |  All 52 grades in the library

← Back to Alloy Grades