Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

ZCuAl9Mn2

9-2 Aluminum Bronze (Aluminum-Manganese Bronze)  |  Cast Copper Alloy  |  GB/T 1176

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Al8.0~10.0
Mn1.5~2.5
CuBalance

Mechanical & Physical Properties

Tensile strength≥440 MPa (chill cast)
Elongation≥20% (chill cast)
Hardness≥95 HBW (chill cast)
Density≈7.6 g/cm³

Typical Applications

bushingsgearsworm wheelspipe fittingspump casings

Grade Overview

An economical aluminum-manganese cast bronze for bushings, gears, worm wheels, pipe fittings and pump casings. Aluminum strengthens the alloy while manganese raises strength and improves casting behaviour, giving a dense structure and good pressure tightness together with useful resistance to seawater and atmospheric corrosion; sand-cast tensile strength is at least 390 MPa and both ductility and fabricability are good. Because it contains neither nickel nor iron it stays relatively cheap. Strength is only moderate and hardness and wear resistance fall short of the iron- and nickel-bearing aluminum bronzes. Use it for fairly simple shapes that must resist corrosion under pressure; watch aluminum burn-off and oxide inclusions during melting, and allow for good fluidity combined with fairly high shrinkage by planning feeding and pouring temperature carefully. Where higher strength or more wear margin is needed, move to an Fe/Ni aluminum bronze. Its good fluidity and pressure tightness suit it to pump and valve housings, and it resists fresh water and seawater well enough for general industrial service.

Selecting ZCuAl9Mn2

Choose ZCuAl9Mn2 where an economical cast aluminum bronze must resist fresh water, seawater and atmospheric corrosion under pressure — bushings, gears, worm wheels, pipe fittings and pump casings. Aluminum strengthens the alloy while manganese raises strength and improves casting behaviour, giving a dense structure and good pressure tightness; sand-cast tensile strength is at least 390 MPa with good ductility, and because it contains neither nickel nor iron it stays relatively cheap. Strength is only moderate, and hardness and wear resistance fall short of the iron- and nickel-bearing aluminum bronzes. Where more strength or wear margin is needed, move to ZCuAl10Fe3 or ZCuAl10Fe3Mn2; where severe seawater service is involved, a nickel aluminum bronze is better. Where cost must be lower still and duty is light, a tin bronze may suffice.

Working with ZCuAl9Mn2

Melting ZCuAl9Mn2 calls for attention to aluminum burn-off and oxide inclusions, which lower properties and casting quality. The alloy has good fluidity but fairly high shrinkage, so feeding and pouring temperature must be planned carefully to avoid shrinkage porosity in heavy sections. It gives pressure-tight castings, which is why pump and valve housings are a natural use. Machining is straightforward for a cast bronze, and the alloy welds acceptably. Because strength and hardness are moderate, do not use it where loads or wear are severe; step up to an iron- or nickel-bearing aluminum bronze if the duty is heavier. Where it works with steel, allow for thermal expansion differences.

Frequently asked questions about ZCuAl9Mn2

Why is ZCuAl9Mn2 cheaper than other aluminum bronzes?

It contains aluminum and manganese but deliberately no nickel or iron, and those elements are what raise the cost of the high-strength aluminum bronzes. Without them the alloy still gives a dense, pressure-tight casting with at least 390 MPa sand-cast tensile strength and good corrosion resistance, which is enough for pump casings, pipe fittings and similar parts. Strength and wear resistance are correspondingly moderate.

Is ZCuAl9Mn2 good for pump casings and pipe fittings?

Yes. Aluminum strengthens the alloy and manganese improves casting behaviour, giving a dense structure and good pressure tightness together with useful resistance to fresh water, seawater and atmospheric corrosion. That combination suits pump casings, valve parts, pipe fittings and similar pressure-containing castings, provided loads and wear are moderate. For heavier or more aggressive duty, an iron- or nickel-bearing aluminum bronze should be used.

What should I watch when casting ZCuAl9Mn2?

Watch aluminum burn-off and oxide inclusions during melting, because both reduce casting quality, and allow for the alloy's good fluidity combined with fairly high shrinkage by planning feeding and pouring temperature carefully. Done well, the result is a dense, pressure-tight casting. Strength and wear resistance remain moderate, so match the grade to the duty rather than to its ease of casting.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related cast copper alloy grades

ZCuPb10Sn10 · ZCuPb15Sn8 · ZCuPb20Sn5  |  All 52 grades in the library

← Back to Alloy Grades