Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

ZCuPb15Sn8

15-8 Lead Bronze (Heavy-Duty Bearing Bronze)  |  Cast Copper Alloy  |  GB/T 1176  |  UNS C93800

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Sn7.0~9.0
Pb13.0~17.0
CuBalance

Mechanical & Physical Properties

Tensile strength≥200 MPa (chill cast)
Elongation≥6% (chill cast)
Hardness≥65 HBW (chill cast)
Density9.2 g/cm³

Typical Applications

heavy-duty bearing shellsrolling-mill bearingsvehicle bearingsbushings

Grade Overview

A lead bronze with a higher lead content than the 10-10 grade, used for heavy-duty bearing shells, rolling-mill bearings, vehicle bearings and bushings, especially at low speed with heavy load and some shock. The larger lead fraction improves sliding behaviour, shock absorption and embeddability beyond the 10-10 grade, so the alloy conforms better to the shaft journal and tolerates brief oil starvation; sand-cast tensile strength is about 170 MPa with elongation of at least 5%. The trade-off is a further fall in strength and hardness, roughly 200 MPa and 65 HBW in chill castings, and weaker fatigue resistance, plus stronger restrictions on lead. Specify it for rolling-mill and vehicle bearing shells, normally cast as a bimetal layer, keep service temperature and speed moderate, and verify the compliance position for leaded material before release. The lead level also drives a density difference that segregation can exploit, so the melt must be stirred thoroughly before pouring, and the journal hardness has to be matched to the soft lining.

Selecting ZCuPb15Sn8

Choose ZCuPb15Sn8 when a bearing shell runs at low speed under heavy, steady load and has to absorb some shock or brief oil starvation. Its higher lead fraction slides and embeds foreign particles better than ZCuPb10Sn10 and conforms to the shaft more readily, so it holds a film where a harder bronze might score. It is not a structural material: chill-cast tensile strength is only about 200 MPa with at least 65 HBW, so parts carrying real tensile or bending load belong to ZCuZn25Al6Fe3Mn3 or an aluminum bronze such as ZCuAl10Fe3. Step up to ZCuPb20Sn5 or ZCuPb30 when the load is light, the speed higher and maximum lubricity is wanted; step back to ZCuSn10P1 or ZCuSn5Pb5Zn5 when more hardness and a lower lead content are required; and choose ZCuAl8Mn13Fe3Ni2 where seawater corrosion, rather than friction, decides the selection.

Working with ZCuPb15Sn8

Lead and copper differ enough in density that ZCuPb15Sn8 segregates if the melt stands, so stir it shortly before pouring and keep the pouring temperature low enough to limit lead settling while still filling the mould. Parts are usually poured as a thin lining bonded to a steel or bronze shell; tin the backing, preheat it so the bond is sound, and cool the lining at a controlled rate. Thin, uniform layers shed heat better than thick ones. No heat treatment is used. The soft lead phase machines freely, so finishing cuts are easy, but handle the swarf under the lead rules that apply to the grade. In service, match journal hardness to the soft lining, keep speed and running temperature moderate, and maintain a generous, clean oil supply.

Frequently asked questions about ZCuPb15Sn8

What load and speed suit ZCuPb15Sn8?

It suits low speed with heavy, steady load. Hardness is at least 65 HBW in chill castings and tensile strength about 200 MPa, so the alloy is a bearing lining rather than a structural material. Keep the specific pressure and speed within the design limits of the shell and maintain oil supply; if speed rises with light load, a higher-lead grade such as ZCuPb20Sn5 runs better.

Can ZCuPb15Sn8 be used in seawater?

It is not the alloy to choose for seawater. A lead-bearing tin bronze has limited resistance to chloride attack, and the lead phase does not help in marine duty. For seawater or brackish water, move to an aluminum bronze such as ZCuAl9Fe4Ni4Mn2 or a cupronickel such as BFe10-1-1. Use this grade where lubrication and embeddability, not corrosion resistance, drive the selection.

Why does the lead content matter for compliance?

Lead is present at 13-17%, and leaded copper alloys face restrictions in drinking-water, food-contact and some export markets. Before release, confirm which rules apply to the destination and the application, and keep the material certificate traceable to the heat. Where lead is not permitted, choose a lead-free alternative such as ZCuSn10Zn2 or ZCuAl10Fe3, accepting the different friction and wear behaviour.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related cast copper alloy grades

ZCuPb20Sn5 · ZCuPb30 · ZCuSn10P1  |  All 52 grades in the library

← Back to Alloy Grades