Shenyang Yuheng Metal Manufacturing
Wear-resistant alloy castings & bearings
HomeProductsArticlesAboutAlloy GradesContact
EN

Home / Alloy Grades / Cast Copper Alloy

ZCuAl10Fe3Mn2

10-3-2 Aluminum Bronze (CuAl10Fe3Mn2)  |  Cast Copper Alloy  |  GB/T 1176

We make this grade. See the finished parts we produce with it  View products

Chemical Composition (%)

Al9.0~11.0
Fe2.0~4.0
Mn1.0~2.0
CuBalance

Mechanical & Physical Properties

Tensile strength≥540 MPa (chill cast)
Elongation≥20% (chill cast)
Hardness≥120 HBW (chill cast)
Density≈7.5 g/cm³

Typical Applications

bushingsworm wheelsvalve bodieswear parts

Grade Overview

A cast aluminum bronze based on ZCuAl10Fe3 with manganese added, used for bushings, worm wheels, valve bodies and wear parts. Manganese strengthens further in solid solution and raises hardness, so strength, hardness and wear resistance all exceed the 10-3 grade while corrosion resistance remains good: chill-cast tensile strength is at least 540 MPa with elongation of at least 20% and hardness of at least 120 HBW. The penalty is slightly lower ductility than ZCuAl10Fe3 and a greater tendency to brittleness, and brazing is again poor. Use it where strength and wear resistance requirements are higher while corrosion resistance still matters. If aluminum and manganese are both near the top of their ranges, take particular care against slow-cooling embrittlement, cool thick walls faster or compensate in the process, and allow for the difference in thermal expansion when it works against steel. It is a useful middle step between the simple 10-3 bronze and the nickel-bearing grades, adding hardness and wear life without the cost of nickel.

Selecting ZCuAl10Fe3Mn2

Choose ZCuAl10Fe3Mn2 where a cast aluminum bronze must give more strength, hardness and wear resistance than ZCuAl10Fe3 while corrosion resistance still matters — bushings, worm wheels, valve bodies and wear parts. Manganese strengthens the alloy in solid solution and raises hardness, so chill-cast tensile strength is at least 540 MPa with elongation of at least 20% and hardness of at least 120 HBW. It is a useful middle step between the simple 10-3 bronze and the nickel-bearing grades, adding hardness and wear life without the cost of nickel. The penalty is slightly lower ductility than ZCuAl10Fe3 and a greater tendency to brittleness, and brazing is poor. Where heavier load, heat or severe seawater duty applies, move to ZCuAl9Fe4Ni4Mn2 or the high-manganese ZCuAl8Mn13Fe3. Where cost dominates and duty is light, ZCuAl9Mn2 will do.

Working with ZCuAl10Fe3Mn2

With ZCuAl10Fe3Mn2, melting must control manganese burn-off and uniformity as well as aluminum content, because loose composition control produces variable properties. If aluminum and manganese are both near the upper end of their ranges, take particular care against slow-cooling embrittlement: cool thick walls faster or compensate in the process, and inspect suspect sections. Gating should avoid hot spots in heavy sections. Machining is only fair, so use sharp tooling and controlled feeds. Brazing is poor, so assemblies are welded or mechanically fixed, with heat input controlled to avoid cracking. Where it works against steel, allow for the difference in thermal expansion, and avoid galvanic coupling with dissimilar metals in aggressive media.

Frequently asked questions about ZCuAl10Fe3Mn2

Why add manganese to ZCuAl10Fe3Mn2?

Manganese strengthens the alloy in solid solution and raises hardness, so the grade reaches at least 120 HBW in chill castings against about 110 HBW for plain ZCuAl10Fe3, with strength around 540 MPa and elongation still at least 20%. The extra hardness and wear resistance suit worm wheels, bushings and wear parts. The trade-off is slightly lower ductility and a greater tendency to brittleness if cooling is uncontrolled.

Is ZCuAl10Fe3Mn2 good for seawater?

It has useful corrosion resistance and is used for valve bodies, pump parts and wear components, but it contains no deliberate nickel, so it is not the strongest choice for severe seawater or impingement service. Where seawater resistance, corrosion-fatigue strength and high strength are all needed, ZCuAl9Fe4Ni4Mn2 is the established nickel aluminum bronze and is the safer specification.

How does it compare with ZCuAl9Mn2?

ZCuAl9Mn2 contains aluminum and manganese but no deliberate iron, so it stays cheaper while giving about 440 MPa tensile strength in chill castings with good casting behaviour and pressure tightness. ZCuAl10Fe3Mn2 has an aluminum-iron base with added manganese, reaching at least 540 MPa and 120 HBW with better wear resistance. Use the simpler grade for easier duty, the iron-bearing grade where wear matters.

Data compiled from current standards; for selection reference only. Ordering is subject to the standard and the mill certificate. Data source: Shenyang Yuheng Metal Manufacturing Co., Ltd. — yuhengmetal.com.

Related cast copper alloy grades

ZCuAl8Mn13Fe3 · ZCuAl8Mn13Fe3Ni2 · ZCuAl9Fe4Ni4Mn2  |  All 52 grades in the library

← Back to Alloy Grades